Use this dialog box to specify the 3D preview settings and visibility of 2D preview in the Design and Calculation tabs in Shaft Component Generator.
|
Access: |
Ribbon: Design tab  Power Transmission panel Shaft  and in the Design or Calculation tab, click Options.
|
3D Preview
|
Section Edge Features (Fillet, Chamfer,...) |
Specify the visibility of 3D edge features. Show - Section edge features is always visible. Hide - Section edge features is hidden. Show Only for Selected Section - 3D edge features is visible for selected section only. |
|
Section Middle Features (Keyway, ...) |
Specify the visibility of 3D middle features. Show - Section middle features is always visible. Hide - Section middle features is hidden. Show Only for Selected Section - 3D middle features is visible for selected section only. |
|
Bores |
Specify the visibility of 3D bores. Show - 3D bores is always visible. Hide - 3D bores is hidden. Show Only for Selected Section - 3D bores is visible for selected section only. |
|
Bore Edge Features (Fillet, Chamfer, ...) |
Specify the visibility of bore edge features. Show - Bore edge features is always visible. Hide - Bore edge features is hidden. Show Only for Selected Section - Bore edge features is visible for selected section only. |
|
Bore Middle Features (Retaining Ring, ...) |
Specify the visibility of bore middle features. Show - Bore middle features is always visible. Hide - Bore middle features hidden. Show Only for Selected Section - Bore middle features is visible for selected section only. |
|
Apply same settings also for 2D preview |
Select to apply the same settings for 2D preview on the Design and Calculation tabs. |
|
If no placement show in default (X-axis, YZ-plane, XY-plane) |
Select to create 3D preview of the shaft in the default position in the graphics window. Note: If you change this option you must restart the Shaft Generator to enable the option.
|
|
Show Shaft Coordinate System |
Select to show 3D shaft coordinate system. |
|
Automatically Scale Loads and Supports |
Select to scale supports and loads while zooming, and set the scale value. Note: This option is available only if you open Options dialog box from the Calculation tab.
|
2D Preview
|
Always Hide |
Select to always hide 2D preview. 2D preview is hidden in the tab (Design or Calculation) where you made the selection. It means that you can have 2D preview hidden independently in Design and Calculation tabs. |
|
Always Show |
Select to always show 2D preview. 2D preview is shown in the tab (Design or Calculation) where you made the selection. It means that you can have 2D preview shown independently in Design and Calculation tabs. |
|
Automatically Scale Loads and Supports |
Select to scale supports and loads while zooming, and set the scale value. Note: This option is available only if you open Options dialog box from the Calculation tab.
|
|
Show Section Features in Calculation Results report |
Select to show section features in the HTML report. Note: This option is available only if you open Options dialog box from the Calculation tab.
|
|
Show Bores and Bores Features in Calculation Results report |
Select to show bores and bore features in the HTML report. Note: This option is available only if you open Options dialog box from the Calculation tab.
|
|
Show Loads&Supports in Calculation Results report |
Select to show loads and supports in the HTML report. Note: This option is available only if you open Options dialog box from the Calculation tab.
|
|
Show Section Features when Calculation/Graph tab is active |
Select to display section features (keyway, groove, wrench opening, for example) in the 2D preview in the Calculation and Graph tabs. |
|
Show Bores and Bores Features when Calculation/Graph tab is active |
Select to display bores and bore features in the 2D preview in the Calculation and Graph tabs. |
|
Show Loads&Supports Designation |
Select to show the loads and supports designation such as F1, F2, q1 in the 2D preview in the Calculation and Graph tabs. Note: This option is available only if you open Options dialog box from the Calculation tab.
|