Extracting a single calculated result

You can calculate a result based on the entire result data set, or you can limit the data to a specific region, such as the cavity region, the runner region, or even a single element. The results are displayed using the utility screen output and written to a single-value result file (study_name.val) in the associated study folder.

There are three pieces of information that are required to perform this type of extraction:
The command line call to extract a single calculated result is:
studyrlt <study> -result <result ID>  -min|-max|-average|-stddev|-count|
                             -node <node number>|-element <element number>
                             [-layer <layer name>|-cavity|-gate|-runner|-sprue]
                             [-component <number> [-anchor <node1> <node2> <node3>]
                             [-unit SI|Metric|English]
where the arguments are defined as follows:
Arguments Description
<study> Study filename with extension.
-result <result ID> Extract a numerical value from the specified result set.
-min Calculate the minimum value of the result data set.
Restriction: Not available for Result ID 1740 (air traps for Dual Domain/Midplane model), which is classified as a highlight data type (HLDT).
-max Calculate the maximum value of the result data set.
Restriction: Not available for Result ID 1740 (air traps for Dual Domain/Midplane model), which is classified as a highlight data type (HLDT).
-average Calculate the average value of the result data set.
Restriction: Not available for Result ID 1740 (air traps for Dual Domain/Midplane model), which is classified as a highlight data type (HLDT).
-stddev Calculate the standard deviation value of the result data set.
Restriction: Not available for Result ID 1740 (air traps for Dual Domain/Midplane model), which is classified as a highlight data type (HLDT).
-count Count the number of entities of the result data set.
Note:
  • For result ID 1722 (weld line) and 1732 (weld and meld line), the number counted by is the number of segments in the weld line or weld/meld line.
  • For result ID 1622 (air traps, 3D model) and 1740 (air traps, Dual Domain/Midplane model), the number counted is the number of air trap locations.
  • For all other NDDT and ELDT results, the -count option counts the number of entities for the specified result ID
-node <node number> Return the result value at a specified node (Example : -node 57).
Restriction: Not available for Result ID 1740 (air traps for Dual Domain/Midplane model), which is classified as a highlight data type (HLDT).
-element <element number> Return the result value at a specified element (Example: -element 23).
Restriction: Not available for Result ID 1740 (air traps for Dual Domain/Midplane model), which is classified as a highlight data type (HLDT).
-layer <layer name> Only consider results in the selected layer.
Restriction: Not available for Result ID 1722 (weld line), 1732 (weld and meld line), 1622 (air traps, 3D model), or 1740 (air traps, Dual Domain/Midplane model).
-cavity Only consider results in the cavity region.
Restriction: Not available for Result ID 1722 (weld line), 1732 (weld and meld line), 1622 (air traps, 3D model), or 1740 (air traps, Dual Domain/Midplane model).
-gate Only consider results in the gate region.
Restriction: Not available for Result ID 1722 (weld line), 1732 (weld and meld line), 1622 (air traps, 3D model), or 1740 (air traps, Dual Domain/Midplane model).
-runner Only consider results in the runner region.
Restriction: Not available for Result ID 1722 (weld line), 1732 (weld and meld line), 1622 (air traps, 3D model), or 1740 (air traps, Dual Domain/Midplane model).
-sprue Only consider results in the sprue region.
Restriction: Not available for Result ID 1722 (weld line), 1732 (weld and meld line), 1622 (air traps, 3D model), or 1740 (air traps, Dual Domain/Midplane model).
-component <number> Component of the result data set to be extracted:
  • 0 = Magnitude (default)
  • 1 = X, 2 = Y, 3 = Z
    Note: Only applicable to vector-based results
-anchor <node1> <node2> <node3> Apply anchor plane defined by nodes 1,2 and 3
Note: Only applicable to warpage results.
-unit <unit system> Show results in the specified unit system:
  • SI (default)
  • Metric
  • English