|
Post |
Description |
|
850SXT |
Cincinnati 850 Talon Lathe |
|
850TC |
Acramatic 850TC control. Inch format, OP STOP after tool changes, BLOCK DELETE (SKIP) at sync blocks. Turn off BLOCK DELETE to access sync block when restarting at other than start of program. Uses TOOL CHANGE location as positioning move in sync blocks. |
|
ANILAMT |
Anilam Lathe |
|
FAN0TC |
Fanuc 0TC controller. Inch format. Supports multiple repetitive cycles (G70/G71) and threading canned cycles (G76). |
|
FAN6TI/M |
Fanuc6T Control (Inch/Metric). General post for Lathes using the Fanuc6T control. The post is designed for computed threading and drilling cycle output, with canned grooving cycle output. |
|
FANUC11T |
Fanuc 11T Lathe |
|
FANUC3T |
Fanuc 3T Lathe. This post is for a Fanuc 3TD control on a Mori Seiki SL - 1. G50's are used on every tool and after completion of the segment it is returned to the Home position by a G28 on the X axis first followed by the Z axis. X axis output is negative for all values since all cutting is done on backside of part. |
|
G10_CYC |
G10 Romi lathe with Fanuc 21i control. Supports Fanuc Canned Cycles: G83 Drilling, G84 Taping G70 Finishing Cycle, G71/72 Roughing Cycles, G76 Threading Cycle. |
|
G30_CYC |
G20 & G30 Romi lathes with Fanuc 21i control. Supports Fanuc Canned Cycles: G83 Drilling, G84 Taping G70 Finishing Cycle, G71/72 Roughing Cycles, G76 Threading Cycle. |
|
GE1050 |
General Electric 1050T Control. This is a general post designed for lathes using the General Electric 1050T control. |
|
HARD6T |
Hardinge Fanuc6T Control (Inch). General post for Hardinge Lathes using the Fanuc6T control. Instead of using G0 for rapid movements it uses feed rates of 200 inches per minute. The post is designed for computed threading, with canned drilling and grooving cycle output. |
|
JLAB73 |
Jones & Lamson Allen Bradley 7365 Control. Jones & Lamson TNC lathes with the Allen Bradley 7365 control. |
|
MAZAK2TI |
Mazak lathe with radius output. Computed thread and groove. G41 left compensation. G42 right compensation. |
|
MAZAKTI |
Mazak lathe with diameter output. Computed drilling and canned thread and groove. G42 left compensation. G41 right compensation. |
|
MORSEK |
Moriseki (Inch). General post for Moriseki lathes. The post is designed for computed drilling, threading and grooving output. |
|
MSL200 |
Moriseki SL200 Lathe. Inch format |
|
NC-RUN |
This is a special post created just for NC-RUN verification, it is based on the okuma OSP5000 control. |
|
NEW6T |
New Hardinge Fanuc6T Control (Inch). This is a modified version of the HARD6T post for Hardinge, It uses G0 for all rapid movements. The post is designed for computed threading, drilling and grooving cycle output. |
|
OK500I/M |
Okuma OSP5000 Control (Inch/Metric). General post for Okuma lathes using the OSP5000 control. The post is designed for canned cycle drilling, threading and grooving output. |
|
OKLC3I/M |
Okuma LC30 Lathe OSP3000 Control(Inch/Metric). General post for Okuma lathes using the OSP3000 control. The post is designed for canned cycle drilling, threading and grooving output. |
|
PATH |
*Bridgeport EZ-Path Lathe (without CSS). This post generates native conversational format programs. |
|
PATH_CYC |
Bridgeport EZ-Path Lathe (without CSS) with canned cycles. Conversational format programs. Supported Canned Cycles: ROUGH, PROFIL, GROOVE, THREAD, and DRILL. |
|
PATHG |
Bridgeport EZ-Path Lathe (without CSS). This post generates G-Code format programs. |
|
PATHS |
*Bridgeport EZ-Path S Lathe (with CSS). This post generates native conversational format programs. |
|
PATHSG |
Bridgeport EZ-Path S Lathe (with CSS). This post generates G-Code format programs. (with CSS) |
|
PP15_CYC |
Bridgeport PowerPath 15 Lathe with canned cycles. Supported Canned Cycles: ROUGH, PROFIL, GROOVE, THREAD, and DRILL. |
|
PPATH |
*Bridgeport Power-Path-15 Lathe. This post generates native conversational format programs. |
|
PPATHG |
Bridgeport Power-Path-15 Lathe. This post generates G-Code format programs. |
|
PTHS_CYC |
Bridgeport EZPath S Lathe (with CSS) with canned cycles. Supported Canned Cycles: ROUGH, PROFIL, GROOVE, THREAD, and DRILL. (with CSS) |
|
ROMI35I |
Romi Lathe. This post is designed for the Romi |
|
SBLI |
South Bend Lathe (Inch) This post is designed for the Magna Turn Slant Bed CNC2000 lathe. |