MVSETUP on a Named Layout in Paper Space

On a named layout, you can insert a title block into the drawing, and create a set of layout viewports in the title block area.

You can specify a global scale as the ratio between the scale of the title block in the layout and what you have created in model space.

To easily specify all layout page settings and prepare your drawing for plotting, you can also use the Page Setup Manager.

When the TILEMODE system variable is off, or when you enter y or press Enter at the Enable Paper Space prompt, the following prompts are displayed.

Align

Pans the view in a viewport so that it aligns with a base point in another viewport. The current viewport is the viewport that the other point moves to.

Angled

Pans the view in a viewport in a specified direction.

The next two prompts specify the distance and angle from the base point to the second point.

Horizontal

Pans the view in one viewport until it aligns horizontally with a base point in another viewport. This option should be used only if the two viewports are oriented horizontally. Otherwise, the view might be panned outside the limits of the viewport.

Vertical Alignment

Pans the view in one viewport until it aligns vertically with a base point in another viewport. This option should be used only if the two viewports are oriented vertically. Otherwise, the view might be panned outside the limits of the viewport.

Rotate View

Rotates the view in a viewport about a base point.

Undo

Reverses operations performed in the current MVSETUP session.

Create

Creates viewports.

Delete Objects

Deletes existing layout viewports.

Create Viewports

Displays options for creating layout viewports.

Layout Number to Load

Controls creation of layout viewports.

Entering 0 or pressing Enter creates no layout viewports.

Entering 1 creates a single layout viewport whose size depends on the following prompts.

Entering 2 creates four layout viewports by dividing a specified area into quadrants. You are prompted for the area to be divided and the distance between the viewports.

The viewing angle for each quadrant is set as shown in the table.

Standard Engineering Viewports

Quadrant

View

Upper-left

Top (XY plane of UCS)

Upper-right

SE isometric view

Lower-left

Front (XZ plane of UCS)

Lower-right

Right side (YZ plane of UCS)

Entering 3 defines a matrix of layout viewports along the X and Y axes. Specifying points at the next two prompts defines the rectangular area that contains the layout viewports. If you have inserted a title block, the Specify First Corner prompt also includes an option for selecting a default area.

If you enter more than one viewport in each direction, prompts are displayed for entering distances between the layout viewports in the X and Y directions.

The array of viewports is inserted into the defined area.

Redisplay

Redisplays the list of viewport layout options.

Undo

Reverses operations performed in the current MVSETUP session.

Scale Viewports

Adjusts the zoom scale factor of the objects displayed in the layout viewports. The zoom scale factor is a ratio between the scale of the border in paper space and the scale of the drawing objects displayed in the viewports.

Interactively

Selects one layout viewport at a time and displays the following prompts for each:

For example, for an engineering drawing at a scale of 1:4, or quarter scale, enter 1 for paper space units and 4 for model space units.

Uniform

Sets the same scale factor for all layout viewports.

Options

Sets the MVSETUP preferences before you change your drawing.

Layer

Specifies a layer on which to insert the title block.

Limits

Specifies whether to reset the grid limits to the drawing extents after a title block has been inserted.

Units

Specifies whether the sizes and point locations are translated to inch or millimeter paper units.

Xref

Specifies whether the title block is inserted or externally referenced.

Title Block

Prepares paper space, orients the drawing by setting the origin, and creates a drawing border and a title block.

Delete Objects

Deletes objects from paper space.

Origin

Relocates the origin point for this layout.

Undo

Reverses operations performed in the current MVSETUP session.

Insert

Displays title block options.

Title Block to Load

Inserts a border and a title block. Entering 0 or pressing Enter inserts no border. Entering 1 through 13 creates a standard border of the appropriate size. The list includes ANSI and DIN/ISO standard sheets.

Add

Adds title block options to the list. Selecting this option prompts you to enter the title block description to be displayed in the list and the name of a drawing to insert.

A line similar to the following example is added after the last entry in the mvsetup.dfs default file:

A/E (24 x 18in),arch-b.dwg,(1.12 0.99 0.00),(18.63 17.02 0.00),in

The last field of the line specifies whether the title block has been created in inches or in millimeters. The units field allows title blocks created in either unit system to be changed by setting the unit type using Options.

You can also add title blocks that have variable attributes.

Delete

Removes entries from the list.

Redisplay

Redisplays the list of title block options.

Undo

Reverses operations performed in the current MVSETUP session.