Target Mapping Dialog Box

Use this dialog box to set and edit the mapping of targets in subassemblies to the names of actual objects in the drawing.

Note: When accessing this dialog box in certain circumstances, the content will be different from what is described in the following section. See Target Mapping Dialog Box (Earlier Version) at the bottom of this topic.

The corridor Target Mapping dialog box is modeless so you can keep it open while you do other work. You can pin the dialog box open so it stays expanded, or you can unpin the dialog box so that only the title is displayed when you move your cursor off the dialog box.

Corridor Name

Displays the name of the selected corridor for which you are setting targets.

Start Station
Displays the start station for the baseline in which the selected subassembly exists.
Note: The Start Station and End Station values update depending on which subassembly is selected.
End Station

Displays the end station for the baseline in which the selected subassembly exists.

Expands the list of targets.
Collapses the list of targets.
Clears all filters from the list.
Note: You can filter the list by clicking the column headings and entering a search term.
Refreshes the list with any changes that have been made to the corridors in the drawing.

Offset and Elevation tab

Use this tab to specify offset and elevation targets.

Click a column heading to display a search box and check boxes which you can use to specify the filter criteria.
Subassembly

Displays the name of the subassemblies that require the targets. Expand the subassembly collections to display the targets to specify for those subassemblies. You can click to expand the list of targets for the subassemblies.

Baseline
Displays the baseline of the corridor.
Note: The baselines that are displayed here are baselines where the assembly is in use and can have targets to other objects.
Region

Displays the region of the corridor in which the subassembly is in use.

Assembly

Displays the assembly in use for the corridor.

Side

Displays the side of the assembly that the subassembly is attached to.

Assembly Group

Displays the name of the assembly group.

Offset

Specifies the offset or width targets. Click in a cell in this column to display the Set Offset Targets controls at the bottom of the dialog box.

Elevation

Specifies the elevation or slope targets. Click in a cell in this column to display the Set Elevation Targets controls at the bottom of the dialog box.

Set Offset Targets/Set Elevation Targets

Use this section of the dialog box to specify the offset/width and elevation/slope targets. The title of this section changes depending on where you have clicked in the dialog box. If you click in a cell in the Offset column, the title is Set Offset Targets. If you click in a cell in the Elevation column, the title is Set Elevation Targets.

Offset Range Filter
Specifies a range by which to filter the available targets. Select the check box and then enter a value to specify the offset. Only those targets that meet the filter requirements are then shown in the Select Entities to Target area.
Select Alignment and Pipe to Target/Select Profile and Pipe to Target
Specifies the alignments or pipes to target for offsets/widths or the profiles or pipes to target for elevations/slopes. The title of this section and the type of entity to specify changes depending on whether you select a cell in the Offset column or the Elevation column. Click to select an object in the drawing. Click to select the object by layer.
Select Feature Lines, Polylines/3D Polylines, and Survey Figures to Target
Specifies the feature lines, polylines, or survey figures to target for offsets/widths or the feature lines, 3D polylines, or survey figures to target for elevations/slopes by selecting them by layer. Select a layer name and then click to refine the selection of objects on that layer if needed. Click to select an object in the drawing.
Dynamic Layer Selection
If a whole layer is selected as the target, new objects can subsequently be added to that layer and will be dynamically added as targets. All objects on the layer must be selected in order for the layer to be dynamic.

To update the corridor after objects on the layer have changed or have been added, one of the following workflows must be used:

  • You must either have the corridor Target Mapping dialog box open when the layer has been changed, or you must reopen the dialog box after the layer has changed.
  • Alternately, you can run the ForceUpdateCorridor command or the ForceUpdateAllCorridors command to force a rebuild of the corridor to apply the changes.
  • The corridor does not get an out of date badge displayed on it in the Prospector tree when the layer has changed. If other aspects of the corridor are out of date which trigger the display of the out of date badge on the corridor in the Prospector tree, then the Rebuild command will also apply the changes from the dynamic layer.
    Note: The Rebuild command does not always work as expected even if a corridor is out of date and the out of date badge appears. The Rebuild command works only when the corridor becomes out of date because of the changes in the same region or the same baseline.
Important: Dynamic layer behavior is not supported for layers in xrefs. If you add an object to a layer in an xref that has been selected as a target in the Target Mapping dialog box, the object will not be automatically selected as a target. To use the new object as a target, you must manually select the object by clicking next to the layer name in the Target Mapping dialog box to display the Select Entities dialog box and then selecting the object in the list.
Selection Choice if Multiple

When specifying an offset target, you can use these settings to specify which offset to target if there are two or more targets in the Select Entities To Target list.

  • Target to Nearest Offset
  • Target to Farthest Offset
  • Target to Flattest Offset
  • Target to Steepest Offset

Surface tab

Use this tab to specify surface targets.

Select a Surface for All Surface Targets
Specifies a surface to assign to all surface targets. If the surface target is the same for all subassemblies, you can use this option instead of assigning each surface target individually.
Subassembly

Displays the name of the subassembly that requires the target.

Baseline

Displays the baseline of the corridor.

Region

Displays the region of the corridor.

Assembly

Displays the assembly in use for the corridor.

Side

Displays the side of the assembly that the subassembly is attached to.

Assembly Group

Displays the name of the assembly group.

Target
Displays the surface target. Click in a cell to select it and then use the drop-down list to select the surface to target.
Rebuild Corridor
Specifies that the corridor will be rebuilt. Select the check box and click Apply or OK to rebuild the corridor.

Context Menu

You can use commands on the context menu to copy targets from one subassembly and paste them to one or more other subassemblies, and to zoom and pan to subassemblies.

Target Mapping Dialog Box (Earlier Version)

Corridor Name

Displays the name of the corridor.

Assembly Name

Displays the name of the assembly. If you are viewing the target for an entire corridor, for which there is more than one baseline, ‘**Varies**’ is displayed.

Start Station

Displays the start station for the assembly’s region or the start station on the corridor baseline. If you are viewing the target for the entire corridor for which there is more than one baseline, ‘**Varies**’ is displayed.

End Station

Displays the end station for the assembly’s region or the end station on the corridor baseline. If you are viewing the target for the entire corridor for which there is more than one baseline, ‘**Varies**’ is displayed.

The properties table contains the following columns:

Target

Lists targets that are required by the corridor’s subassemblies, categorized into three groups: Surfaces, Width Or Offset Targets, and Slope Or Elevation Targets.

Object Name

Opens either the Pick A Surface, Set Width Or Offset Target, Set Slope Or Elevation Target or Select Pipe Network dialog box, where you can select the Autodesk Civil 3D object name to map to the subassembly target.

Note: To quickly set all surface targets to the same surface object, click <Click Here To Set All> next to the Surfaces collection and select the surface object.
Subassembly

Displays the name of the subassembly that requires the target.

Assembly Group

Displays the name of the assembly group.