Key Joint Calculation Formulas in English Units
Transferred torque |
| |
where: |
| | P | power [lb ft] |
| | n | speed [rpm] |
Calculation of Minimum Shaft Diameter
1. shaft inside diameter d h > 0
a) 
b) if d min ≤d h -> d min = 1.1 d h [mm]
c) if d min ≤ 1.5 d h -> d min = 1.5 d h [mm]
2. shaft inside diameter d h = 0
where:
| | d min | minimal shaft diameter [in] |
| | d h | shaft inside diameter [in] |
| | T | torque [Nm] |
| | K a | application factor |
| | K f | fatigue-life factor |
| | S v | desired safety |
| | τ A | Allowable Shear Stress |
| | s | chamfer |
| | p Dmins | minimal allowable pressure (groove, shaft) [MPa] |
| | p Dminh | minimal allowable pressure (groove, hub) [MPa] |
General calculation
| | the range of force activity on the shaft |
h k = h - h s - 2 s [in] | the range of force activity on the hub |
| | shaft diameter of the range of the force activity |
| | hub diameter of the range of the force activity |
| | force on shaft |
| | force on hub |
where: | |
| | T | torque [lbft] |
| | F s | force on shaft [lb] |
| | F h | force on hub [lb] |
| | K a | application factor |
| | K f | wear-life factor |
| | K w | application factor |
| | K m | load distribution factor |
| | S v | desired safety |
| | d | shaft diameter [in] |
| | d s | shaft diameter where force F s actuates [in] |
| | d h | shaft diameter where force F d actuates [in] |
| | N | number of grooves [-] |
| | h | height of groove [in] |
| | h s | height of force point of action on shaft [in] |
| | h h | height of force point of action on hub [in] |
| | b | width of groove [in] |
| | t | groove depth in shaft [in] |
| | s | chamfer |
| | p Dmins | minimal allowable pressure (groove, shaft) [psi] |
| | p Dminh | minimal allowable pressure (groove, hub) [psi] |
Minimum key length to transfer the torque
1. Fixed connection: | a) |
| | b) |
| | L min = min(L mins , L minh ) |
2. Flexible connection: | a) |
| | b) |
| | L min = min(L mins , L minh ) |
where: | |
| | F s | force on shaft [lb] |
| | F h | force on hub [lb] |
| | K a | application factor |
| | K f | wear-life factor |
| | K w | application factor |
| | K m | load distribution factor |
| | S v | desired safety |
| | d | shaft diameter [in] |
| | N | number of grooves [-] |
| | h s | height of force point of action on shaft [in] |
| | h h | height of force point of action on hub [in] |
| | p Dmins | minimal allowable pressure (groove, shaft) [psi] |
| | p Dminh | minimal allowable pressure (groove, hub) [psi] |
Minimal Allowable pressure
1. Fixed connection: | a) |
| | b) |
2. Flexible connection: | a) |
| | b) |
where: | |
| | F s | force on shaft [lb] |
| | F h | force on hub [lb] |
| | K a | application factor |
| | K f | wear-life factor |
| | K w | application factor |
| | K m | load distribution factor |
| | S v | desired safety |
| | d | inside diameter of groove section [in] |
| | N | number of grooves [-] |
| | h s | height of force point of action on shaft [in] |
| | h h | height of force point of action on hub [in] |
| | l f | active key length [in] |
Strength Check
p mins ≤ p Ds
p minh ≤ p Dh
where:
| | p mins | minimal calculated shear pressure in shaft [psi] |
| | p minh | minimal calculated shear pressure in hub [psi] |
| | p Ds | allowable pressure in shaft [psi] |
| | p Dh | allowable pressure in hub [psi] |
Simplified calculation
Minimum key length to transfer the torque
1. Fixed connection: | |
2. Flexible connection: | |
where: | |
| | T | torque [lbft] |
| | K a | application factor |
| | K f | wear-life factor |
| | K w | application factor |
| | K m | load distribution factor |
| | S v | desired safety |
| | d | shaft diameter [in] |
| | N | number of grooves [-] |
| | h | height of groove [in] |
| | s | chamfer |
| | h st | connection height h st = h - 2 s [in] |
| | p Dmin | allowable pressure on supporting surface of shaft, groove, or hub [psi] |
Allowable pressure
1. Fixed connection: | |
2. Flexible connection: | |
where: | |
| | T | torque [lbft] |
| | K a | application factor |
| | K f | wear-life factor |
| | K w | application factor |
| | K m | load distribution factor |
| | S v | desired safety |
| | d | shaft diameter [in] |
| | N | number of grooves [-] |
| | h | height of groove [in] |
| | s | chamfer [in] |
| | h st | connection height h st = h - 2 s [inm] |
| | l f | active key length [in] |
Strength Check
p min ≤ p Ds
p min ≤ p Dh
where:
| | p min | minimal calculated h/2 pressure [psi] |
| | p Ds | allowable pressure in shaft [psi] |
| | p Dh | allowable pressure in hub [psi] |
