VIEWSECTION (Command)

Select parent view

Specifies a view for the section detail.

Start point

Specifies a start point for the section line.

Next point

Specifies the next point for the section line.

Type

The type of section view. The options you can view depend on the type you choose.

Full

Uses the complete view for sectioning.

• Start point. Specifies the first point of the section line.
• End Point. Specifies the second point of the section line.
• Undo. Clears the selected end point.
• Location. Specifies the placement of the section view.

Half

Specifies half of the view is used for sectioning. Once the end point of the section line is specified, the section preview is attached to the cursor, along with the alphabetical section label identifier.

• Start point. Specifies the first point of the section line.
• Next Point. Specifies the next point of the section line.
• Undo. Clears the last selected point.
• End Point. Specifies the last point of the section line.
• Location. Specifies the placement of the section view.

Offset

Specifies that the offset specified by the section is used for cutting the model. You are prompted for the next point until you select Done. Once you select Done, the section view preview is attached to the cursor, along with the alphabetical section label identifier.

• Start point. Specifies the first point of the section line.
• Next Point. Specifies the next point of the section line.
• Undo. Clears the last selected point.
• Done. Specifies the last point of the section line.
• Location. Specifies the placement of the section view.

Aligned

Specifies the section view is always aligned perpendicular to the first or last section line. After the first point, you are prompted for the next point until you select Done. Once you select Done, the section view preview is attached to the cursor, along with the alphabetical section label identifier.

• Start point. Specifies the first point of the section line.
• Next Point. Specifies the next point of the section line.
• Undo. Clears the last selected point.
• Done. Specifies the last point of the section line.
• Location. Specifies the placement of the section view.

Object

Specifies an existing geometry within a view to be used as a section line. Once the existing geometry is selected and the section view is created, the selected geometry is deleted. The section line created from the geometry is associated to the parent view but it is not constrained to the view geometry.

• Select objects. Specifies the geometry used as the section line.
• Done. Specifies the last point of the section line.

Exit

Returns to the previous prompt without selecting a section type.

Representation

This panel is visible only when you have created a section view from an Inventor model. When creating section views, you can only edit the values for Design View.

Hidden Lines

Specifies the display options for the section view.

Visible Lines

Displays the section view in wireframe with only visible lines showing.

Visible and Hidden Lines

Displays the section view in wireframe with both the visible and hidden lines showing.

Shaded with Visible Lines

Displays the section view as shaded, with only visible lines showing.

Shaded with Visible and Hidden Lines

Displays the section view as shaded, with both visible and hidden lines showing.

From Parent

Displays the section view with the property has inherited from the parent base or projected view.

Scale

Specifies the scale of the section view. By default, the scale of the parent view is inherited.

Enter scale

Specify the scale for the section view.

From Parent

Specify the same scale as the parent view. This is the default behaviour.

Visibility

Specify the visibility options to set for the section view. Object visibility options are model specific and some options may not be available in the selected model.

Interference edges

Turns visibility of interference edges on or off. When turned on, the base view displays both hidden and visible edges that are otherwise excluded due to an interference condition.

Tangent edges

Turns visibility of tangent edges on or off. When turned on, the selected view displays a line to show the intersection of surfaces meeting tangentially.

• Tangent edges foreshortened. Shortens the length of tangential edges to differentiate them from visible edges. This is available only if Tangent Edges is selected.

Bend extents

Turns visibility of sheet metal bend extent lines on or off. Sheet metal bend extent lines indicate the location of transition about which a bend hinges or folds, in a flattened sheet metal view.

This option is available only if the corresponding model has a flattened sheet metal view defined in it.

Thread features

Turns visibility of thread lines on screws and tapped holes on or off.

Presentation trails

Turns visibility of presentation trails on or off. Presentation trails are lines in an exploded view (in a presentation file) that show the direction along which a components are moved into assembled position.

Annotation

Identifier

Specifies the label for the section line and the resulting section view.

The program always determines from the drawing, the next free section label. Labels I, O, Q, S, X, and Z are excluded by default, however these can be manually overwritten. You can specify the alphabets to be excluded in the Section View Style Manager dialog box.

Label

Specifies if the section view label text is displayed or not.

Hatch

Specifies whether or not hatch is displayed in the section view.

Exit

Goes back to the previous prompt, or completes the command, depending on where in the command cycle the option appears.