Edit Feature Settings - Alignment Dialog Box

Default Styles

Use these settings to specify the default styles for new alignments.

Alignment Style

Specifies the default alignment style. Click in the Value column, and click to select a style in the Alignment Style dialog box.

Alignment Label Set

Specifies the default alignment label set. Click a cell in the Value column, and click to select the label set in the Alignment Label Set dialog box.

Marker Style

Specifies the display and appearance of points on the alignment. Click in the Value column, and click to select a style in the Marker Style dialog box.

Line Label Style

Specifies the default line label style. Click in the Value column, and click to select a style in the Line Label Style dialog box.

Curve Label Style

Specifies the default curve label style. Click in the Value column, and click to select a style in the Curve Label Style dialog box.

Spiral Label Style

Specifies the default spiral label style. Click in the Value column, and click to select a style in the Spiral Label Style dialog box.

Station Offset Label Style

Specifies the default station offset label style. Click in the Value column, and click to select a style in the Station Offset Label Style dialog box.

Alignment Label Set

Specifies the default alignment label set. Click in the Value column, and click to select a style in the Alignment Label Set dialog box.

Point of Intersection Label Style

Specifies the default point of intersection label style. Click in the Value column, and click to select a style in the Point of Intersection Label Style dialog box.

For information about style selection, see Select Style Dialog Box.

Default Name Format

Use these settings to specify the default name formats for new alignments. Click in the Value column, and click to make changes in the Name Template dialog box.

Station Indexing

Use this setting to specify the default station increment.

Default Station Index Increment

Specifies the default value for station increments.

Superelevation Options

Use these settings to specify defaults for calculating superelevation.

Number of Lanes - Left

Specifies the number of lanes on the left side of the roadway.

Number of Lanes - Right

Specifies the number of lanes on the right side of the roadway.

Roadway Type

Specifies the roadway type as Divided or Undivided.

Cross Section Shape

Crowned: Specifies the cross sectional shape of the roadway as Planar or :

• Planar: There is no change in slope between the travel lanes.
• Crowned: When no superelevation is applied, travel lanes slope downward in opposite directions from a common crown point.

Highside Location (For Undivided Planar Roads)

Specifies the default Highside Location for planar roads.

• Left Edge: Specifies that the high side of the roadway is on the left edge on tangent (unsuperelevated) sections when the corridor type is Undivided and the Cross Section Shape is planar.
• Level: The roadway is level (0% slope) on tangent sections.
• Right Edge: Specifies that the high side of the roadway is on the right edge on tangent (unsuperelevated) sections, when the corridor type is Undivided and the Cross Section Shape is planar.

Normal Lane Width

Specifies the lane width or click and select a distance in the drawing area.

Normal Shoulder Width

Specifies the typical roadway shoulder width.

Normal Lane Slope (%)

Specifies the % slope of the roadway lanes on tangent (unsuperelevated) tangents. Typical values are -15% to -2.5% for the slope used for roadway lanes when no superelevation is applied.

Normal Shoulder Slope (%)

Specifies the % slope value of the roadway shoulders. This value is only required if either of the shoulder superelevation methods is not set to Default. Default value for a normal shoulder slope is -5%.

% On Tangent For Tangent-Curve

percentage of total transition length that is achieved before the beginning of curve (BC) point in tangent-curve geometry.

%On Spiral For Spiral-Curve

percentage of total transition length that is achieved before the beginning of curve (BC) point in spiral-curve geometry.

Station Rounding Option

Specifies the number of positions for station rounding. Click the Value cell and choose one of the following from the list:

• None: leaves stations as they are specified in the table
• 0.1: rounds to the nearest tenth value of the station
• 1: rounds up to nearest full station value
• 5: rounds up to nearest fifth meter or foot
• 10: rounds up to nearest tenth meter or foot

Outside Shoulder Superelevation Method

Specifies the method that is applied to the outside shoulder during superelevation:

• Default Slopes: Default slopes are retained and shoulders are not superelevated.
• Match Lane Slopes: Shoulder slopes match the slopes applied to the adjacent traveled ways through out the superelevation process.
• Breakover Removal: Shoulders on the outside edge of the curve are adjusted upward to match the Normal Lane Slope (%) before the lane begins to superelevate. The high-side shoulder slope matches the high-side lane slope throughout the superelevation process, and it then rotates downward back to the Normal Shoulder Slope (%) value when the lanes are back to the unsuperelevated condition.

Inside Shoulder Superelevation Method

Specifies the method that is applied to the inside shoulder during superelevation:

• Default Slopes: Default slopes are retained and shoulders are not superelevated.
• Match Lane Slopes: Shoulder slopes match the slopes applied to the adjacent traveled ways through out the superelevation process.
• Breakover Removal: Shoulders on the outside edge of the curve are adjusted upward to match the Normal Lane Slope (%) before the lane begins to superelevate. The high-side shoulder slope matches the high-side lane slope throughout the superelevation process, and it then rotates downward back to the Normal Shoulder Slope (%) value when the lanes are back to the unsuperelevated condition.

Design Speed Lookup Method

Specifies the table lookup rule in cases where the actual design speed does not exactly match the speed specified in the design criteria tables:

• Interpolate: Table values are interpolated to the given speed.
• Use Nearest Higher Speed: Uses the table values that correspond to the next highest design speed found in the table. (Conservative rule)
• Round To Nearest Speed: Uses the table values corresponding to the nearest speed, either higher or lower.

Radius Lookup Method

Specifies the table lookup rule in cases where the actual radius does not exactly match the speed specified in the design criteria tables:

• Interpolate: Interpolates table values for the curve group radius.
• Use Nearest Lower Radius: Uses table values corresponding to the next lowest radius found in the table.(Conservative rule)
• Round To Nearest Radius: Uses table values corresponding to the nearest radius value found in the table.

Curve Smoothing Length

Specifies the default curve smoothing length used in superelevation.

Cant Options

Use these settings to specify defaults for calculating cant on Rail alignments.

Equilibrium Cant Formula

Specifies the default formula that calculates how much each rail is raised or lowered to compensate lateral forces due to horizontal curvature. The default formula is:

• Metric: 11.8 * V^2/R
• Imperial: 4.01*V^2/R

Maximum Allowable Cant Deficiency Formula

Specifies the default formula that calculates the maximum allowable cant deficiency value to use in cant calculations. The default formula is:

• Metric: 100mm
• Imperial: 4.00in.

Pivot Method

Specifies the default pivot point location for railways:

• Low Side Rail (Default)
• High Side Rail
• Center Baseline

% on Tangent for Tangent-Curve for Cant

Specifies the percentage of total transition length that is achieved before the beginning of curve (BC) point in tangent-curve geometry. The default percentage is 50.00%.

% on Spiral for Spiral-Curve for Cant

Specifies the percentage of total transition length that is achieved before the beginning of curve (BC) point in spiral-curve geometry. The default percentage is 100.00%.

Maximum Applied Cant on Tangent

Specifies the maximum allowable applied cant on a tangent in tangent-curve situations. The default value is:

• Metric: 25mm
• Imperial: 1.00in.

Station Rounding Option for Cant

Specifies the number of positions for station rounding. Click the Value cell and choose one of the following from the list:

• None (default): leaves stations as they are specified in the table
• 0.1: rounds to the nearest tenth value of the station
• 1: rounds up to nearest full station value
• 5: rounds up to nearest fifth meter or foot
• 10: rounds up to nearest tenth meter or foot

Cant Rounding Options for Equations

Specifies the number of positions for rounding the result of the equilibrium cant and maximum applied cant deficiency calculations. This setting does not affect calculations done in the XML file. The default value is 0.000.

Design Speed Lookup Method for Cant

Specifies the table lookup rule in cases where the actual design speed does not exactly match the speed specified in the design criteria tables:

• Interpolate: Table values are interpolated to the given speed.
• Use Nearest Higher Speed(default): Uses the table values that correspond to the next highest design speed found in the table. (Conservative rule)
• Round To Nearest Speed: Uses the table values corresponding to the nearest speed, either higher or lower.

Radius Lookup Method for Cant

Specifies the table lookup rule in cases where the actual radius does not exactly match the speed specified in the design criteria tables:

• Interpolate: Interpolates table values for the curve group radius.
• Use Nearest Lower Radius (default): Uses table values corresponding to the next lowest radius found in the table.(Conservative rule)
• Round To Nearest Radius: Uses table values corresponding to the nearest radius value found in the table.

Rail Alignment Options

Use these settings to specify default parameters for Rail alignments.

Track Width

Specifies the default distance between the location at which the wheels contact the rails. Track width can also be expressed as the rail gauge minus the rail head width. The default value is:

• Metric: 1.500m
• Imperial: 5.00ft

Degree of Curvature

Use these settings to specify default parameters for measuring alignment geometry using degree of curvature.

Measure Rail Curves Along Chords

Specifies whether to calculate alignment length based on curve chord length, and not true geometry length. The default value is No.

Unit Chord Length

Specifies the default chord length when calculating degree of curvature in Rail alignments. This value must be a positive numeral. The default value is:

• Metric: 30.00
• Imperial: 100.00

Unit Arc Length

Specifies the default arc length used when calculating degree of curvature when an alignment is not measured along chords. This value must be a positive numeral. The default value is:

• Metric: 30.00
• Imperial: 100.00

Linear Transition Around Curves

Use these settings to specify the default settings for how linear transitions around curves are created in widening situations. For more information, see Setting Defaults for Linear Transitions Around Curves in Widenings.

Number of Segments

Specifies how many segments to use when creating linear transitions at curves.

Transition Segment Type

Specifies the type of segments to be used in distributing widening transition linearly around curves. The choices are lines or arcs.

Automatic Widening Around Curves

Use these settings to specify defaults for the Add Automatic Widening command. For more information, see Adding Automatic Widening to Dynamic Offset Alignments

Widening to Apply on

This value, in combination with the Number of Lanes specified in the Widening Method, specifies the amount of widening to be applied on the left-side and or the right-side offset alignments. If Inside Only is used, then the widening value is increased to match the number of lanes on either side of the road (doubled if the number of lanes on the inside and the outside are the same), and applied on all of the inside offset for the widening. On the outside at these stations, no widening is applied.

Wheelbase Length

Specifies a numeric value for the wheelbase length that is used in the formula for widening around curves. This value is used only when the widening method is through design standards. It is not used when the widening is specified manually.

Add Automatic Widening At Curves

Specifies whether or not to automatically add widening at curves.

Widening By

Specifies the default method for applying the automatic widening - either by using design standards, or manually (by entering values into the Increase in Width and Transition Length fields on the Add Automatic Widening dialog box). When Through Design Standards is the default, the Specify Widening Using Criteria option on the Add Automatic Widening dialog box is selected by default. When Manually is the default, the Specify Widening Manually option is selected.

Manual Widening Width

Specifies the default value for the Increase in Width field on the Add Automatic Widening dialog box.

Manual Transition Length

Specifies the default value for the Transition Length field on the Add Automatic Widening dialog box.

Criteria-Based Design Options

Use these settings to specify defaults for creating an alignment using design criteria.

Default Design Speed

Specifies the default alignment design speed. Enter a speed in the Value column or click and select a design speed in the drawing area.

Criteria-Based Design Option

Specifies whether alignments use design criteria by default. If this option is set to False, the remaining Criteria-Based Design Options are not available.

Note

If the Criteria-Based Design Option is set to False, then the remaining Criteria-Based Design Options are not available.

Use Design Criteria File Option

Specifies whether to use a design criteria file by default. If this option is set to True, then the first XML file found in the <install directory>\Data\Corridor Design Standards\<units> directory is used by default.

Use Design Checks Option

Specifies whether to use a design check set by default.

Default Design Check Set

Specifies the default design check set. Click in the Value column, and click to select a set in the Default Design Check Set dialog box.

Check for Tangency Between Elements

Specifies whether to check if any line, curve, or spiral element is not tangent to its previous or next element. If an element is not tangent, then the Warning symbol is displayed in the drawing, in the Alignment Entities vista, and in the Alignment Layout Parameters window.

Dynamic Alignment Highlight Options

Use these settings to specify highlighting defaults for dynamic offset alignments.

Offset Region Color & Lineweight

Specifies the color and lineweight of the highlighting on a dynamic offset alignment region when it is selected in the Offset Alignment Parameters dialog box.

Transition Region Color & Lineweight

Specifies the color and lineweight of the highlighting on the widening transition segment when it is selected in the Offset Alignment Parameters dialog box.

Curb Return Fillet Region Color & Lineweight

Specifies the color and lineweight of the curb return fillet when it is selected in the Intersection Curb Return Parameters dialog box.

Parent Alignment Color & Lineweight

Specifies the color and lineweight of the parent alignment associated with the dynamic offset alignment, when the primary\secondary roads are selected in the Intersection Offset Parameters dialog box, or incoming and outgoing roads are selected in the Intersection Curb Return Parameters dialog box.

Parent Alignment Tracker Color & Lineweight

Specifies the color and lineweight used to identify the tracker line. The tracker line is a temporary line that identifies the corresponding location on the parent alignment when a location on the offset alignment, intersection offset, or curb return is selected in the associated parameters dialog box.

Dynamic Offset Alignment Options

Use these settings to specify the default settings for creating new dynamic offset alignments.

From Parent Alignment Start

Specifies offset alignments to start from the start of the parent alignment.

To Parent Alignment End

Specifies offset alignments to end at the end of the parent alignment.

Number of Offsets - Left Side

Specifies how many offset alignments to create on the left side of the parent alignment when using the create offset alignment command.

Number of Offsets - Right Side

Specifies how many offset alignments to create on the right side of the parent alignment when using the create offset alignment command.

Incremental Offset Value – Left Side

Specifies the incremental offset value to use when creating offset alignments on the left side of a parent alignment. For example, if a value of 5 is specified when there are 2 offsets on the left side, the first offset is created at 5 (feet or meters, depending on units), and the second offset is created at 10 (feet or meters).

Incremental Offset Value – Right Side

Specifies the incremental offset value to use when creating offset alignments on the right side of a parent alignment. For example, if a value of 5 is specified when there are 2 offsets on the right side, the first offset is created at 5 (feet or meters, depending on units), and the second offset is created at 10 (feet or meters).

Implied Point of Intersection Options

Use these settings to specify the default settings for implied points of intersection on alignments.

Implied Point of Intersection Display

Specifies the default method by which implied points of intersection are displayed after an alignment is created.

Constraint Editing Options

Use these settings to specify the default settings for the behavior of the Tangency Constraint (Not Constrained, Constrained by Previous, Constrained by Next, and Constrained on Both Sides) and Parameter Constraint (Radius, Length, Pass Through Point, etc.) while the alignment is edited.

Always Perform Implied Tangency Constraint Swapping

Specifies the default behavior of adjacent subentities when an alignment subentity constraint is changed.

Lock All Parameter Constraints

Specifies whether to lock the Parameter Constraint of every element in the alignment.