Share
 
 

Info360 Trials Demo Workspace

Learn how to set up a workspace using the Info360 Demo Workspace template.

Once you've uploaded the demo sensors and sensor data, you can follow our tutorial to create a workspace from the demo template or follow the instructions in Create a Workspace from a Template.

Set up the Pump Performance Chart

  1. Select the sensors:
    • Flow sensor: P-100_Flow_Rate_Demo
    • Downstream pressure: J1406_Pressure_Demo
    • Upstream pressure: J1404_Pressure_Demo
  2. Save the workspace and select Apply.
  3. Click on the three dots in the top right corner of the chart Configure.
  4. Add a pump status filter for when the sensor P-100_Status_Demo is on.
    1. Click on Source to expand it and then click on Show More Settings.
    2. Under Pump Status Filter, click + Add Sensor and then select P-100_Status_Demo sensor.
    3. Leave the status toggle as On.
    4. Click Update.
  5. Add a pump performance curve.
    1. Go to the References Tab, click on Add Reference, and select Pressure Curve.
    2. Click on Create New Pump Curve.
    3. Upload the Pump.100.PerformanceCurve you downloaded as part of the demo data. The units are gpm and psi.
    4. Click Create.
    5. Select it and then click Add.
  6. Add the pump properties.
    1. Go to the Pump Properties tab and under Pump Rated Capacity fill out:
      • Flow Rate: 1000 gpm
      • Pressure: 145 psi
      • Efficiency: 80 %
      • Brake HP: 105 kW
    2. Under Operating Ranges fill out:
      • AOR: 60 to 140
      • POR: 80 to 120

Set up the Pump Performance Historical Chart

  1. Select the sensors:
    • P-100_Dn_Pressure_Demo
    • P-100_Up_Pressure_Demo
    • P-100_Flow_Rate_Demo
    • P-100_Power_Output_Demo
  2. Save the workspace and select Apply.
  3. Add an additional y-axis for the pressure sensors.
    1. Click on the three dots in the top right corner of the chart Configure.
    2. Click on a pressure sensor, then on Show Source Adjustments
    3. Scroll down and toggle on Show Separate Y-Axis. Set it to the Right.
    4. Click Update.
    5. Select the other pressure sensor Show Source Adjustments Show Separate Y-Axis and this time instead of selecting a new y-axis, select the pressure y-axis you just created (psi).
    6. Click Update again.

Set up the Tank Level Historical Chart

  1. Select the sensor:
    • T5004_Tank_Level_Demo
  2. Save the workspace and select Apply.
  3. Once you save the workspace, you will see there are constant values included representing the maximum and minimum tank level.

Set up the Tank Level Gauge Chart

  1. Select the sensor:
    • T5004_Tank_Level_Demo
  2. Save the workspace and select Apply.
  3. Click on the three dots in the top right corner of the chart Configure.
  4. Set the threshold to 105 to 135.
  5. Click Update.

Set up the Water Quality Historical Chart

  1. Select the sensors:
    • WQ_DMA1_Conductivity_Demo
    • WQ_DMA1_Free_Cl2_Demo
    • WQ_DMA1_Temp_Demo
    • WQ_DMA1_pH_Demo
  2. Save the workspace and select Apply.

Set up the Water Quality Gauge Charts

  1. Select the sensor:
    • WQ_DMA1_pH_Demo (Left) or WQ_DMA1_Free_Cl2_Demo (Right)
  2. Save the workspace and select Apply.
  3. Click on the three dots in the top right corner of the chart Configure.
  4. Set the pH threshold to 7 to 8 (Left) and the Free Cl2 threshold to 1 to 3 (Right).

Was this information helpful?