TARGETPOINT (Command)

Creates a target point light.

List of Prompts

The following prompts are displayed.

Specify source location <0,0,0>: Enter coordinate values or use the pointing device

Specify target location <0,0,-10>: Enter coordinate values or use the pointing device

If the LIGHTINGUNITS system variable is set to 0, the following prompt is displayed:

Enter an option to change [Name/Intensity/Status/shadoW/Attenuation/Color/eXit] <eXit>:

If the LIGHTINGUNITS system variable is set to 1 or 2, the following prompt is displayed:

Enter an option to change [Name/Intensity factor/Status/Photometry/shadoW/Attenuation/filterColor/eXit] <eXit>:

Note: When the LIGHTINGUNITS system variable is set to 1 or 2, the Attenuation option has no affect on the creation of the light. It is only maintained for scripting compatibility.

Name

Specifies the name of the light.

Intensity/Intensity Factor

Sets the intensity or brightness of the light.

Status

Turns the light on and off.

Photometry

Photometry is available when the LIGHTINGUNITS system variable is set to 1 or 2. Photometry is the measurement of the luminous intensities of visible light sources.

In photometry, luminous intensity is a measure of the perceived power emitted by a light source in a particular direction. Luminous flux is the perceived power per unit of solid angle. The total luminous flux for a lamp is the perceived power emitted in all directions. Luminance is the total luminous flux incident on a surface, per unit area.

Intensity

Enter an intensity value in candelas, the perceived power in a luminous flux value, or illuminance value for the total luminous flux incident on a surface.

Candela (symbol: cd) is the SI unit of luminous intensity (perceived power emitted by a light source in a particular direction). Cd/Sr
Lux (symbol: lx) is the SI unit of illuminance. Lm/m^2
Foot-candle (symbol: fc) is the American unit of illuminance. Lm/ft^2

Enter f to specify the perceived power in a luminous flux value.

If you enter i, you can specify the intensity of the light based on an illuminance value.

The illuminance value can be specified in either lux or foot-candles. Enter d to specify a distance to use to calculate illuminance.

Color

Specify the color of the light based on a color name or a Kelvin temperature.

Enter ? to display a list of color names. Enter a text string using wild card characters to display a partial listing of color names, or an asterisk (*) to display all the possible choices.

If you enter k, you can specify the color of the light based on a Kelvin temperature value.

Exit

Exits the command.

Shadow

Makes the light cast shadows.

Off: Turns off the display and calculation of shadows for the light. Turning shadows off increases performance.
Sharp: Displays shadows with sharp edges. Use this option to increase performance.
Soft Mapped: Displays realistic shadows with soft edges.
Map Size: Specifies the amount of memory that should be used to calculate the shadow map.
Softness: Specifies the softness to use to calculate the shadow map.
Soft Sampled: Displays realistic shadows with softer shadows (penumbra) based on extended light sources.
Shape: Specify the shape of the shadow by entering s and then the dimensions of the shape. (For example, the radius of the sphere or the length and width of a rectangle.)

Attenuation

Attenuation Type

Controls how light diminishes over distance. The farther away an object is from a point light, the darker the object appears. Attenuation is also known as decay.

None. Sets no attenuation. Objects far from the point light are as bright as objects close to the light.
Inverse Linear. Sets attenuation to be the inverse of the linear distance from the light. For example, at a distance of 2 units, light is half as strong as at the point light; at a distance of 4 units, light is one quarter as strong. The default value for inverse linear is half the maximum intensity.
Inverse Squared. Sets attenuation to be the inverse of the square of the distance from the light. For example, at a distance of 2 units, light is one quarter as strong as at the point light; at a distance of 4 units, light is one sixteenth as strong.

Use Limits

Specifies whether to use limits or not.

Attenuation Start Limit

Specifies the point where light starts as an offset from the center of the light.

Attenuation End Limit

Specifies the point where light ends as an offset from the center of the light. No light is cast beyond this point. Setting an end limit increases performance where the effect of lighting is so minimal that the calculations are wasted processing time.

Color/Filter Color

Controls the color of the light.

True Color: Specifies a True Color. Enter in the format R,G,B (red, green, blue).
Index: Specifies an ACI (AutoCAD Color Index) color.
HSL: Specifies an HSL (hue, saturation, luminance) color.
Color Book: Specifies a color from a color book.

Exit