Construction Lines Dialog Box (AutoCAD Mechanical Toolset)

Use this dialog box to select from a wide variety of construction line.

Construction Line Mode: Ray Invokes the AMCONSTSWI command such that construction lines are set to Ray.
	AMCONSTHOR Creates a horizontal construction line.
	AMCONSTHW Creates a construction line through a point by specifying an angle relative to an apparent lines that goes that point.
	AMCONSTLOT2 Draws a construction line through a specified point that is perpendicular to the direction specified by another point or angle.
	AMCONSTCC Draws two constructional lines that are tangential to two specified circle.
	AMCONST_CIRCLE Creates a construction line circle.
	AMCONSTVER Creates a vertical construction line.
	AMCONSTPAR Creates a construction line parallel to the existing line at a specified distance.
	AMCONSTHM Creates a construction line that bisects an angle.
	AMCONSTCCREA Draws a construction line circle to represent the top view of a shaft or a hole.
	AMCONSTCIRCLI Creates a construction line rectangle around a circle.
	AMCONSTCRS Creates a construction line cross.
	AMCONSTPAR2 Creates a construction line parallel to an existing line and bisects the distance between the selected line and the specific point or a specified distance.
	AMCONSTTAN Draws two parallel construction lines tangential to a specified circle.
	AMCONSTC2 Creates a construction line circle that uses a specified line as a tangent.
	AMCONSTXRAY Creates construction lines starting from one point and extends to infinity in one direction
	AMCONSTHB Creates a construction line by specifying two points or a point and an angle.
	AMCONSTLOT Draws a construction line that is perpendicular to a specified line.
	AMCONSTTC Draws construction lines that are tangential to two specified circles.
	AMCONSTKR Draws a construction line circle tangential to two specified lines or circles.
	AMCONSTXLINE Draws a construction line through a point, which extends to infinity in both directions.
	AMCONSTZ Creates a construction line in Z direction.
Construction Line Mode: Xline Invokes the AMCONSTSWI command such that construction lines are set to Xline.
	AMCONSTHOR Creates a horizontal construction line.
	AMCONSTHW Creates a construction line through a point by specifying an angle relative to an apparent lines that goes that point.
	AMCONSTLOT2 Draws a construction line through a specified point that is perpendicular to the direction specified by another point or angle.
	AMCONSTCC Draws two constructional lines that are tangential to two specified circle.
	AMCONST_CIRCLE Creates a construction line circle.
	AMCONSTVER Creates a vertical construction line.
	AMCONSTPAR Creates a construction line parallel to the existing line at a specified distance.
	AMCONSTHM Creates a construction line that bisects an angle.
	AMCONSTCCREA Draws a construction line circle to represent the top view of a shaft or a hole.
	AMCONSTCIRCLI Creates a construction line rectangle around a circle.
	AMCONSTCRS Creates a construction line cross.
	AMCONSTPAR2 Creates a construction line parallel to an existing line and bisects the distance between the selected line and the specific point or a specified distance.
	AMCONSTTAN Draws two parallel construction lines tangential to a specified circle.
	AMCONSTC2 Creates a construction line circle that uses a specified line as a tangent.
	AMCONSTXRAY Creates construction lines starting from one point and extends to infinity in one direction.
	AMCONSTHB Creates a construction line by specifying two points or a point and an angle.
	AMCONSTLOT Draws a construction line that is perpendicular to a specified line.
	AMCONSTTC Draws two construction lines that are tangential to two specified circles.
	AMCONSTKR Draws a construction line circle tangential to two specified circles.
	AMCONSTXLINE Draws a construction line through a point, which extends to infinity in both directions.
	AMCONSTZ Draws a construction line along the Z axis.