Revit Structure
Revit Structure| Name | Description |
|---|---|
| Constraints | |
| Level | The level to which the floor is constrained. |
| Height Offset from Level | Specifies the elevation of the top of the floor relative to the Level parameter. |
| Room Bounding | Indicates that the floor is a room-bounding element. |
| Related to Mass | Indicates the element was created from a mass element. This is a read-only value. |
| Structural | |
| Structural | Indicates that the element has an analytical model. |
| Enable Analytical Model | Displays the analytical model and includes it in analytical calculations. Selected by default. See Disabling the Analytical Model. |
| Rebar Cover - Top Face | The rebar cover distance from the floor top face. |
| Rebar Cover - Bottom Face | The rebar cover distance from the floor bottom face. |
| Rebar Cover - Other Faces | The rebar cover distance from the floor to adjacent element faces. |
| Estimated Reinforcement Volume | Specifies the estimated reinforcement volume of the selected element. This is a read-only parameter that only displays when rebar has been placed. |
| Structural Floor Shape Edit | |
| Curved Edge Condition | Specifies the structural floor surface to either Conform to curve or Project to side. This parameter is only available to curved edge structural floors. |
| Dimensions | |
| Slope Angle | Changes the slope-defining lines to the specified value, without the need to edit the sketch. The parameter initially displays a value if there is a slope-defining line. If there is no slope-defining line, the parameter is blank and disabled. |
| Perimeter | The perimeter of the floor. This is a read-only value. |
| Area | The area of the floor. This is a read-only value. |
| Volume | The volume of the floor. This is a read-only value. |
| Thickness | The thickness of the floor. This is a read-only value, unless a shape edit has been applied and its type contains a variable layer. When the value is writable it can be used to set a uniform thickness of the floor. The entry can be blank if the thickness varies. |
| Identity Data | |
| Comments | Specific comments related to the floor that are not already defined in the description or type comments. |
| Mark | A user-specified label for the floor. Possible use: shop mark. This value must be unique for each element in a project. Revit warns you when the number value is already used but allows you to continue using it. You can see the warning using the Review Warnings tool. See Reviewing Warning Messages. |
| Design Option | If design options have been created, this property indicates the design option in which the element exists. For more information see Design Options. |
| Phasing | |
| Phase Created | The phase when the floor was created. See Project Phasing. |
| Phase Demolished | The phase when the floor was demolished. See Project Phasing. |
| Identity Data (Analytical Floors) | |
| Surface Number | An identifier created for the analytical surface. This value should be unique across Analytical Floors, Analytical Foundation Slabs and Analytical Walls in a project. Revit warns you if the number is already used but allows you to continue using it. You can see the warning using the Review Warnings tool. See Reviewing Warning Messages. |
| Comments | User comments. |
| Structural Analysis | |
| Analyze As | Either One-Way or Two-Way. Specifies the transfer of a load through the floor to its supports. |
| Analytical Properties | |
| Family Type | The family type of the element. |
| Physical Material Asset | The name of a physical asset assigned to the floor material (read-only). |
| Area | The total area of the structural floor. |
| Perimeter | The total perimeter of the structural floor. |
| Analytical Alignment | |
| Alignment Method |
Either Auto-Detect or Projection. Specifies if the horizontal and vertical references of the structural floor are automatically justified or have a defined projection. |
| z Projection | Either Top of Element, Center of Element, Bottom of Element, <Level...>, or <Reference Planes...>. Available when Alignment Method is specified as Projection. If in sketch mode, this parameter will default to Floor/Slab edge for either the whole model sketch or just a sketch line. Specifies the vertical limits of the analytical model at the base of the structural floor. |
Related topics