Cool analysis results
This topic specifies the results generated by a Cool analysis for a thermoplastic material. These results can be customized to specific requests for part troubleshooting.
Text based results
The following table lists the text results generated for each Cool analysis.
Graphical results
The following table lists the graphical results generated for a Cool analysis, regardless of the solver, and indicates whether each result is supported for the following analysis technologies:
Results generated only for the Cool (FEM) solver are listed in the next table. Some results, such as Improper part-mold contact, are accessed via 
(Results tab > Plots panel > New Plot).
For more information about a result, including how to interpret the display, click the result name.
| Result | Analysis technology |
|---|
| Average temperature, cold runner result |   |
| Average temperature, part result | |
| Circuit coolant temperature result |  |
| Circuit flow rate result | |
| Circuit heat flux | |
| Circuit heat removal efficiency result | |
| Circuit metal temperature result | |
| Circuit pressure result | |
| Circuit Reynolds number result | |
| Flux, part (top) result | |
| Flux, part (bottom) result | |
| Flux, part result |  |
| Percentage frozen layer result | |
| Percentage frozen layer, cold runner | |
| Temperature, maximum, cold runner | |
| Temperature, maximum, part result | |
| Maximum temperature position, part result | |
| Temperature, internal mold result | |
| Mold-melt temperature difference result | |
| Mold-melt temperature difference (bottom), part result | |
| Mold-melt temperature difference (top), part result | |
| Percentage molten layer result | |
| Frozen layer percentage, part (bottom) result | |
| Frozen layer percentage, part (top) result | |
| Temperature, insert (bottom) result | |
| Temperature, parting plane (bottom) result | |
| Temperature, insert (top) result | |
| Temperature, parting plane (top) result | |
| Temperature at surface, cold runner result | |
| Temperature at surface, hot runner result | |
| Temperature difference, insert result | |
| Temperature difference, part result | |
| Temperature difference, parting plane result | |
| Temperature profile, cold runner result | |
| Temperature profile, hot runner result | |
| Temperature profile, part result | |
| Temperature residual, exterior shell result | |
| Temperature residual, inserts result | |
| Temperature residual, part result | |
| Temperature, mold boundary result | |
| Temperature, mold (top) result | |
| Temperature, mold (bottom) result | |
| Temperature, mold result | |
| Temperature, mold insert result | |
| Temperature, part (top) result | |
| Temperature, part (bottom) result | |
| Temperature, part result | |
| Temperature, part insert result | |
| Time to reach ejection temperature, cold runner result | |
| Time to reach ejection temperature, part | |
Cool (FEM)
The following table lists the graphical results specific to a Cool (FEM) analysis:
| Result | Analysis technology |
|---|
| Improper part-mold contact | |
| Mold parting surface | |
| Rapid heating and cooling circuit density | |
| Rapid heating and cooling circuit flowrate | |
| Rapid heating and cooling circuit pressure | |
| Rapid heating and cooling circuit Reynolds number | |
| Steam condensate mass | |
| Steam quality | |
| Temperature, cartridge heater thermocouples (transient): XY Plot | |
| Temperature, cartridge heater thermocouples (transient from start-up): XY Plot | |
| Temperature, circuit coolant (averaged) | |
| Temperature, circuit coolant (transient) | |
| Temperature, circuit coolant (transient from start-up) | |
| Temperature, core (averaged) | |
| Temperature, core (transient) | |
| Temperature, core (transient from start-up) | |
| Temperature, heater (3D) thermocouples (transient):XY Plot | |
| Temperature, heater (3D) thermocouples (transient from start-up):XY Plot | |
| Temperature, mold (averaged) | |
| Temperature, mold (transient) | |
| Temperature, mold (transient from start-up) | |
| Temperature, mold-cavity interface (averaged) | |
| Temperature, mold-cavity interface (transient) | |
| Temperature, mold-cavity interface (transient from start-up) | |
| Temperature, mold-circuit interface (averaged) | |
| Temperature, mold-circuit interface (transient) | |
| Temperature, mold-circuit interface (transient from start-up) | |
| Temperature, mold insert (averaged) | |
| Temperature, mold insert (transient) | |
| Temperature, mold insert (transient from start-up) | |
| Temperature, mold-insert difference (averaged) | |
| Temperature, mold-insert difference (transient) | |
| Temperature, mold-insert difference (transient from start-up) | |
| Temperature, mold-mold difference (averaged) | |
| Temperature, mold-mold difference (transient) | |
| Temperature, mold-mold difference (transient from start-up) | |
| Temperature, part (averaged) | |
| Temperature, part (average, profile) | |
| Temperature, part (transient) | |
| Temperature, part (transient, profile) result | |
| Temperature, part (transient from start-up) | |
| Temperature, part (transient from start-up, profile) | |
| Temperature, part insert difference (averaged) | |
| Temperature, part insert difference (transient) | |
| Temperature, part insert difference (transient from start-up) | |
| Temperature, rapid heating and cooling thermocouples (transient) | |
| Temperature, rapid heating and cooling thermocouples (transient from startup) | |
| Temperature, runner (averaged) | |
| Temperature, runner (average, profile) | |
| Temperature, runner (transient) | |
| Temperature, runner (transient, profile) | |
| Temperature, runner (transient from start-up) | |
| Temperature, runner (transient from start-up profile) | |
| Time to reach ejection temperature, part (profile) | |
