To create a Probed Ellipse item

Use the Probed Ellipse item to measure a full or partial ellipse on a part. To measure the item, you must measure a minimum of five points distributed around the circumference of the ellipse.

Note: When probe path generation is enabled, you must specify the probing method for the item using the Inspect dialog in the Features tab. You can also use the dialog to view and change some of the item parameters.

To create a Probed Ellipse item:

1. Open a Geometric group in the Sequence Tree.
2. Click Geometry tab > Features panel > Ellipses > Probed Ellipse.

The Probed Ellipse dialog contains the following areas:

Name — Enter a name for the item. The name is used in the inspection sequence, in the Report and Info tabs, and when referencing the item in other items.

Use nominals — Select this check box to enter or change the item nominals, and to compare the item measurements to their nominal values. Deselect this check box to disable comparisons with the item nominals.

When this check box is selected, an in-tolerance or out-of-tolerance indicator is displayed on the measured item's icon in the inspection sequence; the border of the item label is coloured to indicate whether the measurements are within tolerance; and the tolerance, nominal, deviation, and error values of the item are shown in the report.

When this check box is deselected, the Nominal boxes are disabled, no tolerance indicators are displayed and no tolerance, nominal, deviation, and error values are shown in the report for this item.

Note: To load the nominals from the CAD model, click and select From CAD Entity. To replace the nominals with the item's measurements in the current Measure, click the button and select From Active Measure.

Visible — Select this check box to display the item in the CAD view.

Output in report — Select this check box to include the item in the report.

Coordinate system — Select the alignment relative to which the item's measurements are to be reported.

To specify the alignment during the inspection, select <Active Alignment>. You can then select the alignment from the Active alignment list, or by adding an Active Alignment item to the inspection sequence.

Start angle — Enter the start position of the feature relative to the Main axis.

End angle — Enter the end position of the feature relative to the Main axis.

Note: The start and end angles control the display of the item in the CAD view and in full-screen measurement.

Material side — Choose the side from which you want to probe the feature. Select:

• Hole (ID) to probe an internal feature.
• Boss (OD) to probe an external feature.
• Not specified to leave the probing direction unrestricted.

Note: Hole (ID) - Only for CNC and Boss (OD) - Only for CNC provide backwards compatibility for items created in previous versions of PowerInspect. You cannot select these options when creating new items.

Reference plane — Select the plane on which you want to project the feature.

Note: Click to select an item from the CAD view using the mouse.

Centre — Enter the nominal and tolerances for the position of the feature's centre point.

Major axis length — Enter the nominal and tolerances for the length of the feature's longest axis.

Minor axis length — Enter the nominal and tolerances for the length of the feature's shortest axis.

Main axis — Enter the nominal and tolerances for the orientation of the major axis.

Offset/Thickness — By default, the feature is projected onto the reference plane. To specify the position of the feature relative to the reference plane, enter its average height. To calculate the average height of the feature from the measurement, select the Calculate from measurement check box.

Profile — Enter the Maximum difference between the points with greatest positive deviation and greatest negative deviation from the best-fit ellipse. If the difference between the greatest positive deviation and the greatest negative deviation exceeds the Maximum value, the profile is out-of-tolerance.

Guided measure — Select this check box to restrict the probed points to the reference plane when measuring the feature with an articulated arm. Only points taken within the Capture tolerance (specified in the Feature Probing dialog) are recorded. To adjust the plane along its normal, such as when probing a hole, enter an Offset distance. This check box has no effect when probing the part with a CMM.

Auto-accept enabled — Select this check box to save the item measurements as soon as you have probed the number of points specified in the Points box. If you played the item as part of the inspection sequence, PowerInspect automatically plays the next item. Deselect the check box to choose how many points to probe and save your measurements manually. This option is available only when an item has no probe path.

Point sources — Select this tab to use probed points from other items to measure this item.

For example, you can use the tab to create a measured cylinder by combining measurements from probed circles at the top and bottom of the feature.

To specify the sources for the probed points, select one or more items in the Available sources list, and then click to add them to the Selected sources list.

To remove sources, select the items in the Selected sources list, and then click .

Note: You can view the probed points used to measure the item using the Geometric Item Points dialog or the Info tab.

Click OK to close the dialog and save your changes.