Subassembly Reference (continued)

The subassemblies in this subassembly reference are organized alphabetically into the following sections:

Subassembly Reference - BasicBarrier through LaneTowardCrown
Subassembly Reference (continued)- LinkMulti through OverlayWidenWithSuper1 (this section)
Subassembly Reference (continued) - RailSingle through UrbanSidewalk

Topics in this section

LinkMulti
This subassembly is a general purpose subassembly to add a series of connected links.
LinkOffsetAndElevation
This subassembly is a general purpose utility to connect a link from the attachment point to a specified offset and elevation.
LinkOffsetAndSlope
This subassembly is a general purpose utility to connect a link from the attachment point to a specified offset at a given slope.
LinkOffsetOnSurface
This subassembly is a general purpose utility to extend a link from the attachment point to a given offset on a target surface.
LinkSlopeAndVerticalDeflection
This subassembly is a general purpose utility to extend a link at a slope for a vertical deflection distance.
LinkSlopesBetweenPoints
This subassembly is used to insert intersecting links between two points.
LinkSlopeToElevation
This subassembly is a general purpose utility to extend a link at a given slope until it reaches a defined elevation or profile.
LinkSlopeToSurface
This subassembly is a general purpose utility to extend a link from the attachment point at a given slope to the closest intersection with a target surface.
LinkToLaneMarker
This subassembly is a general purpose utility to mark a point on a lane subassembly from the attachment point to a specified width and slope.
LinkToMarkedPoint
This subassembly is a general purpose utility to connect a link from the attachment point to a previously named marked point.
LinkToMarkedPoint2
This subassembly is a general purpose utility that is similar to the LinkToMarkedPoint subassembly, and connects a link from the attachment point to a previously named marked point.
LinkVertical
This subassembly is a general purpose utility to add a vertical surface link by vertical deflection.
LinkWidthAndSlope
This subassembly is a general purpose utility to add a surface link by specifying its width and slope.
LotGrade
This subassembly is used to grade lots from a right of way line.
MarkPoint
This subassembly is used to mark an existing point on the assembly with a name.
MedianConstantSlopeWithBarrier
This subassembly is used to insert a median at the centerline, with asymmetrical barriers on either side of the centerline, and a tapered bottom with an optional key.
MedianDepressed
This subassembly creates a cross-sectional representation of a depressed median between the attachment point and a previously named marked point.
MedianDepressedShoulderExt
This subassembly creates a cross-sectional representation of a depressed median with inside shoulders, using extended termination of shoulder subbase.
MedianDepressedShoulderVert
This subassembly creates a cross-sectional representation of a depressed median with inside shoulders, using vertical termination of shoulder subbase.
MedianFlushWithBarrier
This subassembly inserts surfaces to define a flush median with an optional New Jersey Barrier.
MedianRaisedConstantSlope
This subassembly inserts links for a constant-slope raised median between two points.
MedianRaisedWithCrown
This subassembly inserts links for a constant-slope raised median between two points.
OverlayBrokenBackBetweenEdges
This subassembly is used to overlay a four-lane crowned corridor between gutter flange points on each side, holding to required slope and breakover ranges. This subassembly differs from OverlayBrokenBackOverGutter because it overlays between known flange points, rather than overlaying existing gutter to a known profile on the face of curb.
OverlayBrokenBackOverGutters
This subassembly is used to overlay a four-lane crowned corridor over gutters (between flow lines) on each side, holding to required slope and breakover ranges. This subassembly differs from OverlayBrokenBackBetweenEdges because it overlays existing gutters to a known profile on the curb face, rather than overlaying between known flange points.
OverlayCrownBetweenEdges
This subassembly creates a simple crowned roadway between two edge-of-pavement points.
OverlayMedianAsymmetrical
This subassembly widens an existing divided highway by extending from the travel lane edges inward over a depressed median, with an asymmetrical barrier at the centerline to resolve elevation differences. It includes an option to tie the top-of-barrier elevation to a predefined profile.
OverlayMedianSymmetrical
This subassembly widens an existing divided highway by extending from the travel lane edges inward over a depressed median, with a symmetrical barrier at the centerline. The median slopes may vary somewhat from the existing slopes to make both sides meet at the centerline, or to hold the top of the barrier to a profile.
OverlayMillAndLevel1
This subassembly adds an overlay layer on an existing uncrowned roadway or ramp, with either a leveling and milling layer added as required.
OverlayMillAndLevel2
This subassembly adds an overlay layer on an existing crowned roadway, with either a leveling and milling layer added as required.
OverlayParabolic
This subassembly inserts parabolic travel lanes, to represent finish grade, pavement, and subbase for urban, parabolic lanes between known flange points. The parabolic shape is simulated by a series of short, straight-line links.
OverlayWidenFromCurb
This subassembly is used to overlay one side of an existing road, and add one or more travel lanes to the edge going around a curb return.
OverlayWidenMatchSlope1
This subassembly overlays one side of an existing road, and adds one or more travel lanes to the edge while matching the existing lane slopes.
OverlayWidenMatchSlope2
This subassembly overlays an existing uncrowned road, and adds one or more travel lanes to the left and right edges while matching the existing lane slope.
OverlayWidenWithSuper1
This subassembly overlays one side of an existing road, and adds one or more travel lanes to the edge using the superelevation slope defined for the outside travel lane.